Inspection [08/2016 - ]: Procedure

Refer to PROCEDURE - Step 1 Refer to PROCEDURE - Step 1

See step  2 See step  2

1. Install a camber-caster-kingpin gauge.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Camber-caster-kingpin Gauge

2. Inspect the camber.

   Camber (Unloaded Vehicle)

   Tire Size	Camber Inclination	Right-left Difference
   195/65R15	-1°29' +/- 0°45' (-1.48° +/- 0.75°)	0°45' (0.75°) or less
   205/55R16	-1°29' +/- 0°45' (-1.48° +/- 0.75°)*2 -1°28' +/- 0°45' (-1.47° +/- 0.75°)*1
   215/45R17	-1°28' +/- 0°45' (-1.47° +/- 0.75°)

   *1: for Mexico

   *2: except Mexico

   HINT: 

   Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.

1. Bounce the vehicle up and down at the corners to stabilize the suspension.
2. Release the parking brake and move the shift lever to N (for CVT).
3. Release the parking brake and move the shift lever to neutral (for Manual Transaxle).
4. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
5. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Tread Center Mark
   *b	Dimension B
   	Front of the Vehicle

6. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

   HINT: 

   Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.

7. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Dimension A
   	Front of the Vehicle

   Toe-in (Unloaded Vehicle)

   Tire Size	Specified Condition	Right-left Difference
   195/65R15	C + D: 0°19' +/- 0°17' (0.31° +/- 0.28°)	-
   	B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)	6.0 mm (0.236 in.) or less
   205/55R16	C + D: 0°18' +/- 0°17' (0.29° +/- 0.28°)*2 C + D: 0°14' +/- 0°17' (0.23° +/- 0.28°)*1	-
   	B - A: 3.1 +/- 3.0 mm (0.122 +/- 0.118 in.)*2 B - A: 2.4 +/- 3.0 mm (0.0945 +/- 0.118 in.)*1	6.0 mm (0.236 in.) or less
   215/45R17	C + D: 0°19' +/- 0°17' (0.31° +/- 0.28°)	-
   	B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)	6.0 mm (0.236 in.) or less

   *1: for Mexico

   *2: except Mexico

   HINT: 

   Measure "B - A" only when "C + D" cannot be measured.

   If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.