LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2006 >> Tacoma PreRunner, 2D Pickup >> Repair and Diagnosis >> External Pages >> Different car >> Section 35 (Navigation) >> Navigation System >> DTC 01-DF Master Error >> Inspection Procedure

Inspection Procedure

WARNING: This page is about a different car, the 2006 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Be sure to read DESCRIPTION before performing the following procedures:
  1. CHECK MULTI-DISPLAY POWER SOURCE CIRCUIT 

    Refer to the multi-display power source circuit (See MULTI-DISPLAY POWER SOURCE CIRCUIT ).

    If the power source circuit is operating normally, proceed to the next step.

    NEXT 

  2. INSPECT RADIO RECEIVER 
    1. Disconnect the radio receiver connectors.
    2. Measure the resistance according to the value(s) in the table below.
      STANDARD RESISTANCE SPECIFIED CONDITION

      Tester Connection Condition Specified Condition
      ATX+ (E12-5) - ATX- (E12-15) ((1)) Always 60 to 80
      TX+ (E15-9) - TX- (E15-10) Always 60 to 80
      (1) for 12 Speaker System

    NG: REPLACE RADIO RECEIVER 

    Fig 1: Identifying Radio Receiver Connector Terminals
    G04380211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: GO TO NEXT STEP 

  3. IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE 
    1. Enter the diagnostic mode.
      Fig 2: Display LAN Monitor Mode
      G04380212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Press the "LAN Mon" switch to change to "LAN Monitor" mode.
    3. Identify the component which has stored this code.

      Component Table: 

      COMPONENT REFERENCE

      Display Component
      AUDIO H/U Radio receiver
      DSP-AMP Stereo component amplifier
      G/W Gateway ECU
      NAVI Navigation ECU
      CLOCK Clock assembly

      HINT:

      "NAVI" is the component which has stored this code in the example shown in Fig 2.

    NEXT 

  4. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - COMPONENT WHICH HAS STORED THIS CODE) 

    HINT:

    For details of the connectors, refer to TERMINALS OF ECU .

    1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the multi-display and the component which has stored this code.
      1. Disconnect all connectors between the multi-display and the component which has stored this code.
      2. Check for an open or short in the AVC-LAN circuit between the multi-display and the component which has stored this code.

        OK: 

        There is no open or short circuit. 

        Fig 3: AVC - LAN Wiring Diagram
        G04380213Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: GO TO NEXT STEP 

  5. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - RADIO RECEIVER) 

    HINT:

    For details of the connectors, refer to TERMINALS OF ECU .

    1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the multi-display and the radio receiver.
      1. Disconnect all connectors between the multi-display and the radio receiver.
      2. Check for an open or short in the AVC-LAN circuit between the multi-display and the radio receiver.

        OK: 

        There is no open or short circuit. 

        Fig 4: AVC-LAN Wiring Diagram
        G04380214Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: GO TO NEXT STEP 

  6. REPLACE MULTI-DISPLAY 
    1. Replace the multi-display with a normal one and check if the same problem occurs again.

      OK: 

      Same problem does not occur. 

    NG: REPLACE COMPONENT WHICH HAS STORED THIS CODE 

    OK: END 

scientia non olet · About LEMON Manuals