VSC OFF Indicator Light Remains ON: Procedure

1. Check if a CAN communication system DTC is output. Refer to DIAGNOSIS SYSTEM [07/2013 - 12/2013] .

   Result

   Result	Proceed to
   DTC is not output.	A
   DTC is output.	B

B → See step   14 

A: Go to next step 

1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

   OK

   The connector is securely connected.

NG → CONNECT CONNECTOR TO ECU CORRECTLY 

OK: Go to next step 

1. Check the battery voltage.

   Standard Voltage

   11 to 14 V

NG → See step   13 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Select the Data List using the Techstream. Refer to DATA LIST / ACTIVE TEST [07/2013 - ] .
   ABS/VSC/TRAC
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   TRC(TRAC)/VSC Off Mode	TR(A)C/VSC OFF mode / Normal, TRC(TRAC) OFF or VSC OFF	Normal: Normal mode TRC(TRAC) OFF: TR(A)C OFF mode VSC OFF: VSC OFF mode	-

4. Using the Techstream, check that the switch condition displayed on the Techstream changes according to VSC OFF switch operation.

   OK

   The Techstream display changes according to VSC OFF switch operation.

NG → See step   7 

OK: Go to next step 

1. Select the Data List using the Techstream. Refer to DATA LIST / ACTIVE TEST [07/2013 - ] .
   ABS/VSC/TRAC
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Sports Mode	VSC SPORT mode / Normal or Sports	Normal: Normal mode Sports: VSC SPORT mode	-

2. Using the Techstream, check that the switch condition displayed on the Techstream changes according to VSC SPORT switch operation.

   OK

   The Techstream display changes according to VSC SPORT switch operation.

NG → See step   9 

OK: Go to next step 

1. Perform an Active Test of the combination meter assembly (meter CPU) using the Techstream. Refer to DATA LIST / ACTIVE TEST [07/2013 - 12/2013] .
2. Check the combination meter assembly.

   OK

   The VSC OFF indicator and VSC SPORT indicator lights turn on or off in accordance with the Active Test operation.

   HINT: 

   If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts. Refer to PROBLEM SYMPTOMS TABLE [07/2013 - ] .

NG → See step   12 

OK → See step   11 

1. Remove the VSC OFF switch. Refer to REMOVAL [07/2013 - ] .
2. Inspect the VSC OFF switch. Refer to INSPECTION [07/2013 - ] .

NG → See step   15 

OK: Go to next step 

1. Disconnect the skid control ECU (brake actuator assembly) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A5-12 (CSW1) - D35-5	Always	Below 1 Ω
   A5-12 (CSW1) - Body ground	Always	10 kΩ or higher
   D35-8 - Body ground	Always	Below 1 Ω

   HINT: 

   If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts. Refer to PROBLEM SYMPTOMS TABLE [07/2013 - ] .

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   11 

1. Remove the VSC SPORT switch. Refer to REMOVAL [07/2013 - ] .
2. Inspect the VSC SPORT switch. Refer to INSPECTION [07/2013 - ] .

NG → See step   16 

OK: Go to next step 

1. Disconnect the skid control ECU (brake actuator assembly) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   A5-27(CSW2) - D35-1	Always	Below 1 Ω
   A5-27(CSW2) - Body ground	Always	10 kΩ or higher
   D35-8 - Body ground	Always	Below 1 Ω

   HINT: 

   If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts. Refer to PROBLEM SYMPTOMS TABLE [07/2013 - ] .

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK → See step   11