LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2021 >> RC F Base >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Seat Belt - Service Information >> Front Seat Outer Belt Assembly With Pre-TENSIONER >> Installation [09/2014 - ] >> Procedure

Installation [09/2014 - ]: Procedure

  1. INSTALL OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY 
    1. Engage the clip and install the outer belt anchor bracket sub-assembly with the bolt.

      Torque: 42 N.m (428 kgf/cm, 31 ft.lbf) 

    2. Install the floor carpet.
    3. Engage the guide.
    4. Install the clip.
  2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY 

    See step  1

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY 
    1. Temporarily install the front seat outer belt assembly with the 2 bolts.
      GTY501831Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fully tighten the bolt (A) first, then the bolt (B) to install front seat outer belt assembly.

      Bolt (A) 

      Torque: 12.5 N.m (127 kgf/cm, 9 ft.lbf) 

      Bolt (B) 

      Torque: 42 N.m (428 kgf/cm, 31 ft.lbf) 

    3. Connect the pretensioner connector and lock the locking button as shown in the illustration.
      GTY497463Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Locking Button
      *b Lock
      NOTE:

      Securely lock the locking button.

    4. Connect the connector.
    5. Connect the shoulder anchor of the front seat outer belt assembly with the bolt.

      Torque: 42 N.m (428 kgf/cm, 31 ft.lbf) 

    6. Check that the ELR locks.
      NOTE:

      The check should be performed with the front seat outer belt assembly installed to the vehicle.

      1. With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.
  4. INSTALL CENTER PILLAR GARNISH ASSEMBLY 

    Refer to PROCEDURE - Step 20 [09/2014 - 11/2017] , or refer to PROCEDURE - Step 19 [11/2017 - ]

  5. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY 

    Refer to PROCEDURE - Step 21 [09/2014 - 11/2017] , or refer to PROCEDURE - Step 20 [11/2017 - ]

  6. INSTALL REAR SIDE SEATBACK ASSEMBLY 

    Refer to PROCEDURE - Step 2

  7. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY 

    See step  10

  8. CONNECT FRONT SEAT OUTER BELT ASSEMBLY 
    1. Connect the floor anchor of the front seat outer belt assembly with the nut as shown in the illustration.

      Torque: 42 N.m (428 kgf/cm, 31 ft.lbf) 

      GTY521017Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Tongue Plate
      *b Floor Anchor
      NOTE:

      When connecting the floor anchor of the front seat outer belt assembly, make sure that the tongue plate is facing the front of the vehicle.

  9. INSTALL LAP BELT OUTER ANCHOR COVER 
    1. Engage the guide.
    2. Engage the 2 claws to install the lap belt outer anchor cover.
  10. INSTALL REAR SEAT CUSHION LOCK HOOK 

    Refer to PROCEDURE - Step 6

  11. INSTALL REAR SEAT CUSHION ASSEMBLY 

    Refer to PROCEDURE - Step 7

  12. INSTALL FRONT DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 38 [09/2014 - 11/2017] , or refer to PROCEDURE - Step 37 [11/2017 - ]

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [09/2014 - 08/2016] , or refer to INITIALIZATION [08/2016 - 11/2017] , or refer to INITIALIZATION [11/2017 - 03/2019] , or refer to INITIALIZATION [03/2019 - 01/2023] , or refer to INITIALIZATION [01/2023 - 10/2023] , or refer to INITIALIZATION [10/2023 - ]

  14. INSPECT SRS WARNING LIGHT 

    Refer to DIAGNOSIS SYSTEM [09/2014 - 11/2017] , or refer to DIAGNOSIS SYSTEM [11/2017 - ]

scientia non olet · About LEMON Manuals