Removal [10/2014 - ]: Procedure

Refer to PROCEDURE - Step 11

Refer to PROCEDURE - Step 12

Refer to PROCEDURE - Step 14

Refer to PROCEDURE - Step 8 [10/2014 - 09/2017], or refer to PROCEDURE - Step 8 [09/2017 - ]

Refer to PROCEDURE - Step 9 [10/2014 - 09/2017], or refer to PROCEDURE - Step 9 [09/2017 - ]

Refer to PROCEDURE - Step 10 [10/2014 - 09/2017], or refer to PROCEDURE - Step 12 [09/2017 - ]

HINT: 

Use the same procedure described for the LH side.

Refer to PROCEDURE - Step 5 [10/2014 - 09/2017], or refer to PROCEDURE - Step 5 [09/2017 - ]

Refer to PROCEDURE - Step 6 [10/2014 - 09/2017], or refer to PROCEDURE - Step 6 [09/2017 - ]

HINT: 

Use the same procedure described for the LH side.

Refer to PROCEDURE - Step 14 [10/2014 - 09/2017], or refer to PROCEDURE - Step 16 [09/2017 - ]

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 3

HINT: 

Use the same procedure described for the LH side.

Refer to PROCEDURE - Step 11 [10/2014 - 09/2017], or refer to PROCEDURE - Step 11 [09/2017 - ]

1. Disconnect the rear window defogger connector.
2. Remove the bolt and ground wire.
3. Detach the 2 clamps.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

4. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	No. 3 Window Glass Spacer
   *2	No. 4 Window Glass Spacer
   *a	Piano Wire
   	Protective Tape

   Apply protective tape to the outer surface of the vehicle body to prevent scratches.

   NOTE:

   When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

5. From the interior, insert a piano wire between the vehicle body and back door glass as shown in the illustration.
6. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

7. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Matchmark

   Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

   HINT: 

   Matchmarks do not need to be placed if the glass is not going to be reused.

8. Cut through the adhesive by pulling the piano wire around the back door glass.
   NOTE:

   Leave as much adhesive on the vehicle body as possible when removing the back door glass.

9. Using suction cups, remove the back door glass.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. When reusing the back door glass:
   1. Using a scraper, remove the back window outside moulding.
      NOTE:

      • Be careful not to damage the back door glass.
      • Be sure to replace the back window outside moulding with a new one.

1. When reusing the back door glass:
   1. Using a scraper, remove the back door glass spacer.
      NOTE:

      • Be careful not to damage the back door glass.
      • Be sure to replace the back door glass spacer with a new one.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *1	Back Door Glass Spacer
      *a	Back Side

1. When reusing the back door glass:
   1. Using a scraper, remove the No. 3 back window glass spacer.
      NOTE:

      • Be careful not to damage the back door glass.
      • Be sure to replace the No. 3 back window glass spacer with a new one.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Use the same procedure described for the No. 3 back window glass spacer.