Installation [10/2014 - ]: Procedure

1. Install the rear speed sensor LH with the bolt.

   Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

   NOTE:

   • Prevent foreign matter from attaching to the rear speed sensor tip.
   • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the rear axle carrier.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install sensor clamp A together with sensor clamp B with the nut.

   Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

   NOTE:

   Do not twist the wire harness for the sensor clamp when installing it.

3. Install sensor clamp A together with sensor clamp B with the nut.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

   NOTE:

   Do not twist the wire harness for the sensor clamp when installing it.

4. Install sensor clamp C with the nut.

   Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

   NOTE:

   Do not twist the wire harness for the sensor clamp when installing it.

5. Connect the connector.
6. Install the sensor clamp to the side member with the bolt.

   Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

7. Insert the connector and grommet into the inside of the vehicle through the passage hole in the wheel house.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Grommet
   *2	Connector
   *3	Grommet Band Clamp
   *a	Inside of Vehicle

   NOTE:

   Make sure the grommet band clamp remains on the outside of the vehicle.

8. Hold the grommet and pull it toward the outside of the vehicle. Then fix the grommet in place so that it is not tilted.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Outside of Vehicle

   *b

   30°

   NOTE:

   • When pulling out the grommet, do not grip the sensor wire.
   • Fix the grommet in place within the range shown in the illustration.
9. Connect the 2 connectors.

1. Install the rear speed sensor LH with the bolt.

   Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

   NOTE:

   • Prevent foreign matter from attaching to the rear speed sensor tip.
   • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the rear axle carrier.
2. Install the sensor clamp with the nut.

   Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

3. Install the 2 sensor clamps to the upper arm with the 2 nuts.

   Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

   NOTE:

   Do not twist the wire harness for the sensor clamp when installing it.

4. Install the sensor clamp to the side member with the bolt.

   Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

   NOTE:

   Do not twist the wire harness for the sensor clamp when installing it.

5. Insert the connector and grommet into the inside of the vehicle through the passage hole in the wheel house.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Grommet
   *2	Connector
   *3	Grommet Band Clamp
   *a	Inside of Vehicle

   NOTE:

   Make sure the grommet band clamp remains on the outside of the vehicle.

6. Hold the grommet and pull it toward the outside of the vehicle. Then fix the grommet in place so that it is not tilted.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Outside of Vehicle

   *b

   30°

   NOTE:

   • When pulling out the grommet, do not grip the sensor wire.
   • Fix the grommet in place within the range shown in the illustration.
7. Connect the connector.

Refer to INSTALLATION [10/2014 - 09/2015] , or refer to INSTALLATION [09/2015 - 09/2017] , or refer to INSTALLATION [09/2017 - 05/2019] , or refer to INSTALLATION [05/2019 - ]

Refer to INSTALLATION [10/2014 - ]

Refer to TEST MODE PROCEDURE [10/2014 - 05/2019] , or refer to TEST MODE PROCEDURE [05/2019 - ]