LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2016 >> IS 300 Base >> Repair and Diagnosis >> Body & Frame >> Windows >> Window / Glass - Service Information >> Rear Power Window Switch >> Inspection [04/2013 - ] >> Procedure

Inspection [04/2013 - ]: Procedure

  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) 
    1. Check the switch function.
      GTY458186Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH Door))
      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        2 (UP) - 5 (GND) Auto up or up position Below 1 Ω
        10 (DOWN) - 5 (GND) Auto down or down position Below 1 Ω
        4 (AUTO) - 5 (GND) Auto up or auto down position Below 1 Ω
        2 (UP) - 5 (GND) Off 10 kΩ or higher
        10 (DOWN) - 5 (GND) Off 10 kΩ or higher
        4 (AUTO) - 5 (GND) Off 10 kΩ or higher

        If the result is not as specified, replace the rear power window regulator switch assembly (for LH door).

    2. Check that the LED illuminates.
      GTY458185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH Door))
      1. Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

        OK

        Measurement Condition Specified Condition
        Battery positive (+) → 8 (LED)
        Battery negative (-) → 5 (GND)        		 LED illuminates

        If the result is not as specified, replace the rear power window regulator switch assembly (for LH door).

  2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) 
    1. GTY458186Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Door))

      Check the switch function.

      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection Condition Specified Condition
        2 (UP) - 5 (GND) Auto up or up position Below 1 Ω
        10 (DOWN) - 5 (GND) Auto down or down position Below 1 Ω
        4 (AUTO) - 5 (GND) Auto up or auto down position Below 1 Ω
        2 (UP) - 5 (GND) Off 10 kΩ or higher
        10 (DOWN) - 5 (GND) Off 10 kΩ or higher
        4 (AUTO) - 5 (GND) Off 10 kΩ or higher

        If the result is not as specified, replace the rear power window regulator switch assembly (for RH door).

    2. GTY458185Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Door))

      Check that the LED illuminates.

      1. Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

        OK

        Measurement Condition Specified Condition
        Battery positive (+) → 8 (LED)
        Battery negative (-) → 5 (GND)        		 LED illuminates

        If the result is not as specified, replace the rear power window regulator switch assembly (for RH door).

scientia non olet · About LEMON Manuals