Diagnostic Aids

When using the Evaporative Emission System Tester (EEST) to apply pressure, you can regulate the amount of pressure by activating the remote switch on and off while observing pressure in the EVAP system using a scan tool. DO NOT use more than 5 inches H2O. More than 5 inches H2O applied to the EVAP system can cause the canister vent solenoid valve to temporarily remain in the closed position, which could lead to misdiagnosis in this procedure.
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP vent solenoid inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.
For intermittent conditions refer to Intermittent Conditions .

DTC P0446

Step	Action	Values	Yes	No
Schematic Reference: Evaporative Emissions (EVAP) Hose Routing Diagram
1	Did you perform the Diagnostic System Check - Vehicle?	-	Go to Step 2	Go to Diagnostic System Check - Vehicle
2	Inspect the evaporative emission (EVAP) system for the following conditions: A damaged EVAP canister vent solenoid valve-Refer to Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement . A pinched EVAP vent hose A damaged EVAP canister-Refer to Evaporative Emission (EVAP) Canister Replacement . Did you find and correct the condition?	-	Go to Step 15	Go to Step 3
3	Turn OFF the ignition. Disconnect the purge line from the EVAP canister purge solenoid valve. Refer to Evaporative Emission (EVAP) Canister Purge Solenoid Valve Replacement (L36) or Evaporative Emission (EVAP) Canister Purge Solenoid Valve Replacement (L67) . Turn ON the ignition, with the engine OFF. Is the Fuel Tank Pressure sensor parameter within the Specified range?	-1 to +1 in H2O	Go to Step 4	Go to Step 10
4	IMPORTANT: Do not exceed the specified value in this step. Exceeding the specified value may produce incorrect test results. Turn OFF the ignition. Reconnect the EVAP purge pipe. Connect the J 41413-200 Evaporative Emissions System Tester (EEST) power supply clips to a known good 12-volt source. See Special Tools . Install the J 41415-40 Fuel Fill Cap Adapter to the fuel fill pipe. See Special Tools . Connect the fuel fill cap to the J 41415-40 . See Special Tools . Connect the J 41413-200 nitrogen/smoke supply hose to the J 41415-40 . See Special Tools . Turn ON the ignition with the engine OFF. Command the EVAP canister vent solenoid valve closed with a scan tool. Turn the nitrogen/smoke valve on the J 41413-200 control panel to NITROGEN. See Special Tools . Use the remote switch to pressurize the EVAP system to the first specified value. Observe the Fuel Tank Pressure sensor parameter with a scan tool. Command the EVAP canister vent solenoid valve open with a scan tool. Is the Fuel Tank Pressure sensor parameter less than the second specified value?	5 in H2O 1 in H2O	Go to Step 5	Go to Step 7
5	Connect the nitrogen/smoke hose to the EVAP service port. Remove the J 41415-40 . See Special Tools . Install the fuel fill cap to the fuel fill pipe. Start the engine. Allow the engine to idle. Use the purge/seal function to seal the system with a scan tool. Command the EVAP canister purge solenoid valve to 30 percent. Observe the vacuum/pressure gage on the J 41413-200 and the FTP parameter on the scan tool. See Special Tools . Allow the vacuum to increase on the gage of the J 41413-200 until it reaches approximately 16 in H2O. See Special Tools . Use the purge/seal function to seal the system with a scan tool. Is the FTP parameter on a scan tool within the specified value of the vacuum/pressure gage on the J 41413-200 until the vacuum reached the abort limit on a scan tool?	1 in H2O	Go to Step 6	Go to Step 10
6	Did the FTP parameter on a scan tool display more than the specified value?	3.2 V	Go to Diagnostic Aids	Go to Step 12
7	Disconnect the EVAP vent hose from the EVAP canister vent solenoid valve. Is the Fuel Tank Pressure sensor parameter less than the specified value?	1 in H2O	Go to Step 13	Go to Step 8
8	Disconnect the EVAP vent hose from the EVAP canister. Is the Fuel Tank Pressure sensor parameter less than the specified value?	1 in H2O	Go to Step 9	Go to Step 14
9	Repair the pinched or restricted EVAP vent hose. Did you complete the repair?	-	Go to Step 15	-
10	Test for an intermittent and for a poor connection at the fuel tank pressure (FTP) sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition?	-	Go to Step 15	Go to Step 11
11	Test the low reference circuit of the FTP sensor for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	-	Go to Step 15	Go to Step 12
12	Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement . Did you complete the replacement?	-	Go to Step 15	-
13	Replace the EVAP canister vent solenoid valve. Refer to Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement . Did you complete the replacement?	-	Go to Step 15	-
14	Replace the EVAP canister. Refer to Evaporative Emission (EVAP) Canister Replacement . Did you complete the replacement?	-	Go to Step 15	-
15	Perform the Service Bay Test. Refer to Service Bay Test . Does the scan tool indicate that the Service Bay Test passed?	-	Go to Step 16	Go to Step 3
16	Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed?	-	Go to Diagnostic Trouble Code (DTC) List - Vehicle	System OK